501-30 Funilaria traseira

501-30-1 Rear End Sheet Metal Repairs 501-30-1 . SECTION 501-30 Rear End Sheet Metal Repairs VEHICLE APPLICATION: 2011.50 Ranger CONTENTS REMOVAL AND INSTALLATION Back Panel – Single Cab.................................................................................................. Back Panel – Double Cab................................................................................................. Back Panel – Super Cab................................................................................................... PAGE 501-30-2 501-30-5 501-30-8

501-30-2 Rear End Sheet Metal Repairs 501-30-2 REMOVAL AND INSTALLATION Back Panel – Single Cab General Equipment Spot weld drill Bit Removal 1. Remove the load body. E139841 3. Mill out the spot welds. General Equipment: Spot weld drill Bit 2. Mill out the spot welds. General Equipment: Spot weld drill Bit

501-30-3 Rear End Sheet Metal Repairs 501-30-3 REMOVAL AND INSTALLATION E139842 Installation 1. NOTE: Before resistance spot welding of body panels with a total panel thickness of 3 mm and greater, the manufacturer's welding equipment instructions and sub-section 501-25 must be followed. Refer to: Tools and Equipment for Body Repairs (501-25 Body Repairs - General Information, Description and Operation). 2. NOTE: Sealer or adhesive must not be applied in welding zones. Areas which were bonded or sealed needs to be thoroughly sealed afterwards. Refer to: Sealer, Underbody Protection Material and Adhesives (501-25 Body Repairs - General Information, Description and Operation). 3. ‡ Resistance spot weld - Panel thickness 3 mm and greater.

501-30-4 Rear End Sheet Metal Repairs 501-30-4 REMOVAL AND INSTALLATION E139843 4. ‡ Resistance spot weld - Panel thickness 3 mm and greater. E139840 5. Install the load body.

501-30-5 Rear End Sheet Metal Repairs 501-30-5 REMOVAL AND INSTALLATION Back Panel – Double Cab General Equipment Spot weld drill Bit Removal 1. Remove the load body. E139804 3. Mill out the spot welds. General Equipment: Spot weld drill Bit 2. Mill out the spot welds. General Equipment: Spot weld drill Bit

501-30-6 Rear End Sheet Metal Repairs 501-30-6 REMOVAL AND INSTALLATION E139805 Installation 1. NOTE: Before resistance spot welding of body panels with a total panel thickness of 3 mm and greater, the manufacturer's welding equipment instructions and sub-section 501-25 must be followed. Refer to: Tools and Equipment for Body Repairs (501-25 Body Repairs - General Information, Description and Operation). 2. NOTE: Sealer or adhesive must not be applied in welding zones. Areas which were bonded or sealed needs to be thoroughly sealed afterwards. Refer to: Sealer, Underbody Protection Material and Adhesives (501-25 Body Repairs - General Information, Description and Operation). 3. ‡ Resistance spot weld - Panel thickness 3 mm and greater.

501-30-7 Rear End Sheet Metal Repairs 501-30-7 REMOVAL AND INSTALLATION E139806 4. ‡ Resistance spot weld - Panel thickness 3 mm and greater. E139807 5. Install the load body.

501-30-8 Rear End Sheet Metal Repairs 501-30-8 REMOVAL AND INSTALLATION Back Panel – Super Cab General Equipment Spot weld drill Bit Removal 1. Remove the load body. E139858 3. Mill out the spot welds. General Equipment: Spot weld drill Bit 2. Mill out the spot welds. General Equipment: Spot weld drill Bit

501-30- Rear End Sheet Metal Repairs 501-30- REMOVAL AND INSTALLATION E139859 Installation 1. NOTE: Before resistance spot welding of body panels with a total panel thickness of 3 mm and greater, the manufacturer's welding equipment instructions and sub-section 501-25 must be followed. Refer to: Tools and Equipment for Body Repairs (501-25 Body Repairs - General Information, Description and Operation). 2. NOTE: Sealer or adhesive must not be applied in welding zones. Areas which were bonded or sealed needs to be thoroughly sealed afterwards. Refer to: Sealer, Underbody Protection Material and Adhesives (501-25 Body Repairs - General Information, Description and Operation). 3. ‡ Resistance spot weld - Panel thickness 3 mm and greater.

501-30-10 Rear End Sheet Metal Repairs 501-30-10 REMOVAL AND INSTALLATION E139860 4. ‡ Resistance spot weld - Panel thickness 3 mm and greater. E139861 5. Install the load body.